http://funkadelic.org/gallery/main.php Stock front brake (passenger side) http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aaa.jpg.html 610 Once you get the tab lifted up a bit you can twist the sensor 90 degrees counterclockwise and then lift up and out http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aad.jpg.html 617 Twist-on crimp to connect the wires http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aaf.jpg.html 621 Driver side caliper and rotor off http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aag.jpg.html 623 Driver side rotor and caliper removed http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aah.jpg.html 625 Backside of the caliper and rotor http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aai.jpg.html 627 Non-directional vanes on the stock rotor http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aaj.jpg.html 629 Driver side brake installed! http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aap.jpg.html 633 APR "SureStop" pads...back side (L) and friction side (R) http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aas.jpg.html 635 anti-sqeal goo that i picked up from the auto parts store http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aat.jpg.html 637 tightening on the bolt-on bridge (5mm allen wrench) after installing the pads http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aau.jpg.html 639 SS braided brake line w/washers and bolt ready to go on http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aav.jpg.html 641 SS line connected to the caliper http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aax.jpg.html 643 breaker bar (or torque wrench in this case) used to loosen the 2-18mm bolts securing the stock caliper (instructions said 17mm). http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/aba.jpg.html 649 Stock 321mm x 30mm (L) vs. APR 332mm x 32mm (R) rotor http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abc.jpg.html 655 Wow, now i need 355mm rotors!!! http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abd.jpg.html 661 http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abe.jpg.html 663 http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abf.jpg.html 665 plenty of clearance (1/4") on my 18x8.5" BBS CH's http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abk.jpg.html 667 Brake pad wear sensor connector...i chewed up the securing tab nicely http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abp.jpg.html 613 The sensor mounts in this braket and the tab secures in the little hole at the bottom. Wish I knew that before hand (not clearly http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abq.jpg.html 615 Snipping the brake pad wear sensor wires off the stock pads http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abr.jpg.html 619 Mounting bracket in place, about to remove the brake shield (held on by 3-10mm bolts) http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abs.jpg.html 631 Stock rubber brake line attached to the metal brake line to be replaced by the SS one. (nut loosened in this pic..it's starting http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abt.jpg.html 645 http://funkadelic.org/gallery/v/cars/mods/brakes/apr_brakes_install/abu.jpg.html 647